The New Holland Workmaster 60 is a 2WD or 4WD utility tractor from the Workmaster series. This tractor has been manufactured by New Holland (a part of CNH) since 2015. The New Holland Workmaster 60 is equipped with a 2.2 L (136.0 cu·in) three-cylinder diesel engine and a synchronized shuttle transmission with 8 forward and 8 reverse gears.
The NH Workmaster 60 utility tractor used the FPT R753 engine. It is a 2.2 L, 2,229 cm2, (136.0 cu·in) three-cylinder natural aspirated diesel engine with 94.0 mm (3.7 in) of the cylinder bore and 107.0 mm (4.21 in) of the piston stroke. This engine produced 60.8 PS (44.7 kW; 60.0 HP) at 2,600 rpm of output power.
The Workmaster 60 is equipped with power steering, wet disc brakes, two-post folding ROPS and 52.2 liters (13.8 US gal.; 11.5 Imp. gal) fuel tank.
Following attachments are available for the NH Workmaster 60 utility tractor:
- New Holland 611TL loader
- New Holland 616TL loader
- New Holland 621TL loader
- New Holland 626TL loader
- New Holland 935GHB backhoe
New Holland Workmaster 60 Specifications
| General Specifications | |
| Model | New Holland Workmaster 60 |
| Length | 2WD: 3,280 mm (129.1 in) 4WD: 3,400 mm (133.9 in) |
| Width | 1,960 mm (77.2 in) |
| Height (ROPS) | 2,470 mm (97.2 in) |
| Wheel base | 2WD: 2,440 mm (96.1 in) 4WD: 2,470 mm (97.2 in) |
| Weight | 2WD: 2,015 kg (4,442 lbs) 4WD: 2,295 kg (5,060 lbs) |
| Fuel tank capacity | 52.2 liters (13.8 US gal.; 11.5 Imp. gal) |
| Battery | 12V |
| Cabin type | Two-post folding ROPS |
| Engine | |
| Engine model | FPT R753 |
| Engine type | Four-stroke, liquid-cooled, inline |
| Cylinders | 3 |
| Fuel type | Diesel |
| Displacement | 2.2 L, 2,229 cm2, (136.0 cu·in) |
| Bore and stroke | 94.0 mm X 107.0 mm (3.7 in X 4.21 in) |
| Horsepower | 60.8 PS (44.7 kW; 59.9 HP) at 2,600 rpm |
| Starter | Electric |
| Transmission and chassis | |
| Chassis | 4×2 2WD or 4×4 MFWD 4WD |
| Steering type | Power |
| Brakes | Wet disc |
| Transmission model | – |
| Transmission type | Synchronized shuttle |
| Gears | 8 forward and 8 reverse |
| Tires | |
| Front tires | Ag: 7.5×16 (2WD), 9.5×24 (4WD) Industrial: 12.5×18 |
| Rear tires | Ag: 14.9×28 Industrial: 18.4×24 |
| Three-Point Hitch | |
| Category | II/I |
| Control type | Position and draft control |
| Lift capacity (at ends) | 1,500 kg (3,310 lbs) |
| PTO (Power take-off shaft) | |
| Rear PTO type | Independent with mechanical clutch |
| Rear PTO speed | 540 or 540/540E rpm |
| Hydraulic system | |
| Hydraulic type | Open center |
| Valves | 1 or 2 |
| Pump flow | 12.0 gpm (45.4 lpm) |
| Steering flow | 5.5 gpm (20.8 lpm) |
| Total flow | 17.5 gpm (66.2 lpm) |
I need to know why my titan 7 foot bushog driveshaft gets cut in two ( I have gone through two ) from rubbing on the deck of cutter. I am the owner of a new holland work master 60 tractor.