Zetor 6320

Zetor 6320The Zetor 6320 is a 2WD utility tractor manufactured by Zetor in Brno, Czech Republic from 1993 to 1997. The Zetor 6320 is equipped with a 3.9 L (239.0 cu·in) four-cylinder diesel engine and one of two transmissions: a synchromesh transmission with 10 forward and 2 reverse gears and hydraulic cerametallic disc clutch or a mechanical shuttle transmission with 10 forward and 10 reverse gears.

The Zetor 6320 utility tractor used the Zetor Z7701 engine. It is a 3.9 L, 3,916 cm2, (239.0 cu·in) four-cylinder natural aspirated diesel engine with 102.0 mm (4.02 in) of the cylinder bore and 120.0 mm (4.72 in) of the piston stroke. The compression ratio rating is 17.0:1. This engine produced 66.9 PS (49.2 kW; 66.0 HP) at 2,200 rpm of output power.

The Zetor 6320 is equipped with power steering, hydraulic dry disc brakes, two-post ROPS or Cab. and 70.0 liters (18.5 US gal.; 15.4 Imp. gal) fuel tank.

Zetor 6320 Specifications

General Specifications
ModelZetor 6320
Length3,650 mm (143.7 in)
Width1,850 mm (72.8 in)
Height2,640 mm (103.9 in)
Wheel base2,230 mm (87.8 in)
Ground clearance530 mm (20.9 in)
Weight3,040 kg (6,702 lbs)
Fuel tank capacity70.0 liters (18.5 US gal.; 15.4 Imp. gal)
Battery12V, CCA 950A
Cabin typeTwo-post ROPS or Cab.
Engine
Engine modelZetor Z7701
Engine typeFour-stroke, liquid-cooled, inline
Cylinders4
Fuel typeDiesel
Displacement3.9 L, 3,916 cm2, (239.0 cu·in)
Bore and stroke102.0 mm X 120.0 mm (4.02 in X 4.72 in)
Compression ratio17.0:1
Horsepower66.9 PS (49.2 kW; 66.0 HP) at 2,200 rpm
StarterElectric
Transmission and chassis
Chassis4×2 2WD
Steering typePower
BrakesHydraulic dry disc
Transmission model
Transmission typeSynchromesh hydraulic cerametallic disc clutch
Gears10 forward and 2 reverse
Speed Forward: 23.8 kmh (14.8 mph) Reverse: 7.0 kmh (4.4 mph)
Transmission model
Transmission typeMechanical shuttle
Gears10 forward and 10 reverse
Speed Forward: 23.8 kmh (14.8 mph) Reverse: kmh (0 mph)
Tires
Front tires Ag: 9.00-16
Rear tires Ag: 16.9-34
Three-Point Hitch
CategoryII/I
Control typePosition and draft control
Lift capacity (at ends)2,655 kg (5,855 lbs)
PTO (Power take-off shaft)
Rear PTO typeIndependent
Rear PTO speed540/1000 rpm
Hydraulic system
Hydraulic typeOpen center
Pressure2600 psi (179.3 bar)
Valves1 to 3
Pump flow11.0 gpm (41.6 lpm)
Steering flow4.0 gpm (15.1 lpm)
Total flow15.0 gpm (56.8 lpm)
ATTENTION! Dear visitors, this site is not a trading platform, an official dealer or a spare parts supplier, so we do not have any price lists, spare parts catalogs, service or owner manuals. We are an information portal and provide the technical specifications.

We try to use verified sources and official documentation, however, differences between sources or errors in entering information may occur. In addition, the characteristics may vary depending on the modification and market. We do not provide advice on technical issues related to the any operation or repair. We do not recommend using provided information for repairing or spare parts ordering, use only official service manuals and spare-parts catalogs.

Be the first to comment

Leave a Reply

Your email address will not be published.


*